--------------------------------------------------------------------------------
	Infineon TPM 1.2 FieldUpgrade-Tool "TPMFU"
	      Infineon Technologies AG
--------------------------------------------------------------------------------

Contents:

1. Welcome
1.1 Prerequisites
1.2 Installation
1.3 Operation

2. If you have questions

3. Release Info
3.1 About this Release
3.2 Hardware and Software Platform Requirements
3.4 Known Bugs and Limitations

================================================================================

1. Welcome

Welcome to Infineon TPM 1.2 FieldUpgrade-Tool "TPMFU". 

The TPM 1.2 FieldUpgrade-Tool "TPMFU" is intended to be used to upgrade the
Firmware of the Infineon Technologies TPM SLB9635TT1.2 from the Version 01.00
to the Version 01.02.


1.1 Prerequisites

PC compatible platforms, MS-DOS 6.22 and later, running from 1,44MB Floppy Disk,
HDD or bootable USB-Stick. Additionally, as operation in memory-mapped mode is
supported, a DPMI server (like CWSDPMI.EXE) is required. CWSDPMI can be obtained
via this link: http://clio.rice.edu/cwsdpmi/csdpmi5b.zip

Note:
By default, CWSDPMI requires a swap file located at C:\. To avoid problems, it is
recommended to install a RAMDISK at C:\ with 4MByte or more, or to make sure that
the HDD can be accessed from DOS for this purpose.


1.2 Installation

Unzip TPM_0102.ZIP into a single folder on a HDD, where MS-DOS is installed
or onto a bootable MS-DOS Floppy Disk or USB-Stick. It is recommended to load
CWSDPMI as a TSR at Boot-Time, so that it is available when the TPMFU is started.


1.3 Operation

TPMFU is operated as follows:

Call: TPMFU
Calling without parameter starts the FieldUpgrade process.
First the TPM is checked wether it is enabled and activated, if not, it will be
enabled and activated if PhysicalPresence is not locked by the Platform BIOS. If this
was successfull a reboot is required to complete this step. If not, this step must be
done manually via the appropriate BIOS Setup Page.
Thereafter, the current version info is read out and displayed, and if the current
FW Version can be upgraded, the Fieldupgrade-Process is performed.
After the Fieldupgrade, a TPM_SelftestFull is executed, the TPM is left in it's
enabled and activated state.

Call: TPMFU -help or -?
This option displays a small help-screen which shows the usage options for TPMFU.

Call: TPMFU -info
This option displays only the detailed information about the current state of the TPM,
like ROM-CRC, current FW version, Fieldupgrade-State. A Fieldupgrade itself is not
performed.

Call: TPMFU -disable
This option does the same as if called without parameter, but after the upgrade process
the TPM will be deactivated and disabled.

Call: TPMFU -noselftest
This option does the same as if called without parameter, but the TPM_SelftestFull
after the upgrade process will be omitted.


Options in TPMFU.CFG:
[LOGGING_LEVEL]
LEVEL = 0

This key is for development purpose only, leave setting at 0 to avoid runtime problems.

[BASE_Address]
IO_BASE = 0x4700
CFG_BASE = 0x4E

Base address values used for legacy communication protocol (I/O-mapped).

IO_BASE is the Runtime address for the TPM which is configured by the
platform Bios in the PC Chipset.

CFG_BASE is the Config address for the TPM which is configured by the
platform Bios in the PC Chipset.

Please consider that the TPMFU.EXE does not configure the PC chipset and
therefore relys on a proper setting of the PCI to LPC bridge.

[TIMEOUT]
BWT = 60
CWT = 6

Timeout values used for legacy communication protocol (I/O-mapped). Do not change.

[INTERRUPT]
IRQ_NUMBER = 0x00
IRQ_CONTROL = 0x02

Interrupt settings, currently not used by the tool. Do not change.

[ACCESS_MODE]
USE_LEGACY = 1
LOCALITY = 0

This key specifies via which interface the TPM is used.

USE_LEGACY enables the tool to use the I/O-mapped interface if set to 1, otherwise
if set to 0 Memory-mapped interface (TIS) is used.

LOCALITY specifies the Locality (between 0 and 4) which is used if Memory-mapped
interface is selected.


2. If you have questions

If you have any questions or problems, please contact your local Infineon Representative. 

Further information is available under http://www.infineon.com/tpm


3. Release Info

3.1 About this Release

This release contains the 
- TPMFU.EXE
This is the TPM 1.2 FieldUpgrade-Tool.
- 4 Files *.01
Those files are used during the FieldUpgrade process, please do not modify or remove.
- TPMFU.CFG
This file is used to specify the usage parameters for the TPMFU.EXE.
Please adjust the settings to comply with your platform.
- Readme.txt
This file.


3.2 Hardware and Software Platform Requirements

Hardware Requirements: 

   - A PC compatible platform equipped with an Infineon TPM 1.2.

Software Requirements for TPM 1.2 FieldUpgrade-Tool "TPMFU":

   - MS-DOS 6.22 and later
   - CWSDPMI or equivalent


3.4 Known Bugs and Limitations
The Fieldupgrade is only possible if there is no Owner installed on the TPM to be
upgraded. If an Owner is installed, this must be cleared manually before e.g. via the
appropriate BIOS Setup Page.









